| Traverse Data and Crater DTMs |
| The following rover traverse data
and crater DTMs (digital terrain models) were produced by the Ohio
State University Mapping and GIS Laboratory. The quality of these
products is not optimal due to time constraints. After the mission
operation period, products are expected to be refined and final
versions will be made available. The products are referenced to
their respective landing site local frames, which are centered at
each lander with X, Y and Z-axes pointing to east, north and upward.
Contact: Prof. Ron Li Director, Mapping and GIS Lab The Ohio State University 470 Hitchcock Hall, 2070 Neil Avenue Columbus, OH 43210-1275 Tel. (614) 292-6946 Fax. (614) 292-2957 E-mail: li.282@osu.edu |
| Data Product | File | Contents |
| Spirit Traverse Data | MERA_Traverse_Sol 1-2169.txt (24 KB) | ASCII text table with columns for sol #, site #, position #, and x (east), y (north), z (up) coordinates. These traverse points are bundle adjusted incrementally. Site and position values are expressed using an alphanumeric scheme that is described in detail on page 25 of the Camera SIS (http://pds-geosciences.wustl.edu/mer/mer1-m-pancam-2-edr-sci-v1/mer1pc_0xxx/document/camera_dpsis.pdf). |
| Opportunity Traverse Data | MERB_Traverse_Sol 1-3510.txt (44 KB) | ASCII text table with columns for sol #, site #, position #, and x (east), y (north), z (up) coordinates. After Sol 62, bundle adjustment based rover localization was impossible due to insufficient localization image data. We corrected the 2D rover positions by comparison of craters and other features observed from rover imagery and orbital imagery. Therefore we don't have Z values of the rover locations. Site and position values are expressed using an alphanumeric scheme that is described in detail on page 25 of the Camera SIS (http://pds-geosciences.wustl.edu/mer/mer1-m-pancam-2-edr-sci-v1/mer1pc_0xxx/document/camera_dpsis.pdf). |
| Spirit traverse orthophoto |
orthophoto_molacontrolled.tif (92 MB) Description Document for... .pdf (186 KB) |
Reprojected HiRISE orthophoto of Spirit traverse site based on MOLA-controlled bundle adjustment. See the accompanying document for processing details. |
| Opportunity traverse orthophoto |
MERB_HiRISE_Ortho_MOLAControlled.tif (15 GB) |
Reprojected HiRISE orthophoto of Opportunity traverse site based on MOLA-controlled bundle adjustment. |
| Eagle Crater DTM, binary format |
eagle_dtm_binary.bin (68 MB) eagle_dtm_binary_header.txt (2 KB) |
The .bin file is a generic binary file with the elevation value of each cell (pixel) stored sequentially line by line from the upper left corner to lower right corner. The header file (_header.txt) is a plain text file; it provides necessary information for reading the binary file including number of rows and columns, data type (IEEE 32 bit float), byte_order (Motorola or Intel), X coordinate of upper left corner, Y coordinate of upper left corner, X coordinate of lower right corner, Y coordinate of lower right corner, pixel (cell) width, pixel height, map unit, and so on. |
| Eagle Crater DTM, ASCII format | eagle_dtm_ascii.txt (3 MB) | The format is the same ASCII grid format as that of Surfer (a 3D surface display software system). The first line is a unique identifier "DSAA". Line 2 specifies the number of columns and rows. Lines 3 and 4 give the minimum and maximum coordinates of X and Y, respectively, to define the boundaries of the grid. Line 5 contains the smallest and largest elevation value of the grid. Afterwards, the elevation values are stored line by line from the bottom (south). Within each line, the elevation values are stored from left (west) to right (east). |
| Endurance Crater DTM, binary format |
endurance_dtm_binary.bin (28 MB) endurance_dtm_binary_header.txt (2 KB) |
The .bin file is a generic binary file with the elevation value of each cell (pixel) stored sequentially line by line from the upper left corner to lower right corner. The header file (_header.txt) is a plain text file; it provides necessary information for reading the binary file including number of rows and columns, data type (IEEE 32 bit float), byte_order (Motorola or Intel), X coordinate of upper left corner, Y coordinate of upper left corner, X coordinate of lower right corner, Y coordinate of lower right corner, pixel (cell) width, pixel height, map unit, and so on. |
| Endurance Crater DTM, ASCII format | endurance_dtm_ascii.txt (1 MB) | The format is the same ASCII grid format as that of Surfer (a 3D surface display software system). The first line is a unique identifier "DSAA". Line 2 specifies the number of columns and rows. Lines 3 and 4 give the minimum and maximum coordinates of X and Y, respectively, to define the boundaries of the grid. Line 5 contains the smallest and largest elevation value of the grid. Afterwards, the elevation values are stored line by line from the bottom (south). Within each line, the elevation values are stored from left (west) to right (east). |